Savage MSR 15 Recon Problems And Their Solutions

Are you encountering any common problems with your Savage MSR 15 Recon? If so, you’re not alone.

Many owners of the Savage MSR 15 Recon have experienced similar difficulties in using the rifle, and it can be a challenge to diagnose and fix these issues.

In this article, we’ll explore some of the most common Savage MSR 15 Recon problems, including Failure to Eject, Sight Misalignment, Gas System Blockage, Jamming Issues, Light Primer Strike Issues, Trigger Assembly Problems, Barrel Issues, Feed Ramp issues, Bolt Carrier Group Component Failures, and Unreliable Magazine Feed.

Savage MSR 15 Recon Problems

We’ll also provide some tips on preventing and fixing these problems so that your Savage MSR 15 Recon can perform at its peak.

So, read on to learn more about the most common Savage MSR 15 Recon issues and how to tackle them.

Common Savage MSR 15 Recon Problems And Their Solutions

1. Failure to Eject

When a Savage MSR 15 Recon experiences “Failure to Eject”, it usually means that the firearm is failing to eject an empty case from the chamber forcefully.

This can be caused by a few factors, including a dirty or improperly lubricated weapon, weak spring tension on the extractor, and magazine issues.

The first step is to disassemble and visually inspect the firearm for any dirt, debris, oil buildup, or a weak spring on the extractor.

Also, check that all magazines are properly inserted into place with no damage.

If the issue persists, it is recommended to have a certified gunsmith take a look at the firearm to inspect for any further issues.

2. Sight Misalignment

If you’ve recently purchased a MSR 15 Recon rifle, you may have encountered issues with the sight misalignment.

To align the sights on your rifle, first confirm that your scope rings are securely mounted and that the bases are properly installed onto the receiver.

Then ensure the scope is centered in the rings and the screws on each side are tightened evenly. Finally, adjust windage and elevation as necessary to align your sights.

If these steps do not resolve your sight misalignment issue, you may need a new set of scope rings or bases to achieve optimal alignment.

If so, consider replacing those components with improved designs designed to provide a superior and more accurate fit.

3. Gas System Blockage

Your MSR 15 Recon may have developed a blockage in its gas system. This can occur due to carbon build up from unburned powder, poor lubrication, or an obstruction of some kind in the gas system itself.

If this occurs, here are a few steps you can take to troubleshoot and correct the issue:

  1. Inspect the gas system for any signs of debris, damage, or obstructions that could be causing a blockage.
  2. Clean the gas system thoroughly with cleaner and compressed air to remove any dirt or debris build-up.
  3. Ensure your firearm is lubricated properly according to the manufacturer’s instructions and the environment you plan to use it in.
  4. Check that all gas system components are functioning correctly and not blocked or restricted.
  5. If the issue persists, contact Savage MSR’s customer service team for further assistance with troubleshooting your gun’s gas system blockage.

4. Jamming Issue

The rifle may sometimes experience a jamming issue due to an obstruction in the barrel or excessive gunpowder residue.

This type of jamming is also known as “stove-piping” and can be avoided by cleaning your weapon regularly.

To properly clean the gun, you must disassemble it and then use a special cleaning rod with either brass or stainless steel bore brushes.

Also, make sure that all of the components are properly lubricated after reassembly.

If these methods do not work, you may want to invest in an aftermarket barrel for your Savage MSR 15 Recon rifle.

Aftermarket barrels can often help reduce jamming issues due to their tighter tolerances and improved manufacturing process.

Furthermore, if you are looking for even more enhanced performance, you may want to consider getting a new trigger for your rifle.

This can help reduce the creep and over-travel that can often lead to jamming issues.

5. Light Primer Strike

The rifle has a known issue with the light primer strike, causing misfires and unreliable performance.

This issue is typically caused by an incorrect setting of the firing pin safety, which can be easily remedied by simply adjusting the setting.

If your rifle is experiencing primer strikes, please consult your owner’s manual and adjust this setting as instructed to resolve the issue.

6. Trigger Assembly Problems

If you are experiencing problems with your MSR 15 Recon’s trigger assembly, then you may need to inspect and adjust the trigger.

Adjusting the trigger involves inspecting the components of the trigger assembly such as the hammer, sear, disconnector, springs, pins, etc.

Ensuring all components are properly installed is important to guarantee optimal gun performance.

Sometimes, you may need to replace a faulty part or upgrade worn parts. When replacing these parts, it’s important to use only OEM manufacturer-approved components designed specifically for your Savage MSR 15 Recon to ensure proper performance and safety.

If adjusting the trigger assembly does not solve the problem, then a qualified gunsmith should have the gun serviced.

7. Barrel Issues

The MSR 15 Recon rifle has been known to have some barrel issues, including bulging, cracking, and muzzle wear.

These issues can be caused by various factors such as improper maintenance or excessive heat build-up from rapid firing. To prevent these issues from occurring, we suggest the following tips:

  • Regularly inspect your barrel to check for any signs of damage or wear.
  • Ensure that the barrel is always clean and free from debris, as this can cause heat build-up during rapid firing.
  • Use a bore guide when cleaning your rifle to ensure that the cleaning rod properly aligns with the barrel chamber.
  • When using a suppressor, ensure the barrel is still properly aligned.
  • If you are using your rifle for rapid fire or any other type of high-volume shooting, give your barrel a break in between shots and allow it to cool off before continuing. This will help dissipate heat build-up and reduce the chance of damage or wear.

8. Feed Ramp Issue

The feed ramp issue occurs when there is an obstruction in the rifle’s magazine well, causing a malfunction with the weapon’s feeding system.

This can lead to rounds failing to chamber properly, resulting in jams and misfires. To help resolve this, Savage Arms has included an adjustable feed ramp on their MSR 15 Recon series of rifles.

This allows the shooter to use the flexible length and angle adjustments to ensure optimal feeding performance.

The adjustable feed ramp is easily accessed by unscrewing the two screws located at the rear of the magazine well.

When adjusted correctly, you’ll be able to see a noticeable difference in your rifle’s performance.

You can also increase the power of ammunition by slightly increasing the angle and length of the ramp to help ensure a smoother transition from magazine to chamber.

9. Bolt Carrier Group Component Failures

some users have experienced issues with components of its Bolt Carrier Group (BCG), such as broken extractors or carrier key screws coming loose after only a few rounds fired.

If you’re considering purchasing an MSR-15 Recon and want to avoid any BCG component failures, it’s important to understand the common causes of these problems.

The most frequent cause is improper installation of the bolt carrier key screws when assembling the rifle.

If these screws are not installed properly and securely, they can come loose after only a few rounds and cause various issues such as broken extractors and misfires.

To ensure your MSR-15 Recon’s BCG components perform reliably, installing the bolt carrier key screws according to the manufacturer’s instructions and using a thread locker such as Loctite 243 is recommended.

Also, it’s important to regularly inspect those screws for any signs of wear or loosening after firing and tighten them if necessary.

Finally, you should consider replacing the bolt carrier key screws if worn or stripped, as this could increase the chances of component failure.

10. Unreliable Magazine Feed

Some users have encountered issues with its magazine feed. The magazine feed on the MSR 15 is unreliable and can cause the rifle to misfire or fail to eject spent casings properly.

This issue may be caused by an inadequate design of the magazine well, which prevents it from gripping the magazine securely and reliably.

To address this issue, users can try to modify the magazine well of their Savage MSR 15 Recon rifle.

If modifications do not help, it is best to consult with a qualified gunsmith who may be able to improve the reliability of the magazine feed.

Furthermore, compatibility issues between magazines and rifles may also cause problems and should be checked.


The Savage MSR 15 Recon rifle is an exciting and powerful firearm. Its effective range, high accuracy, and lightweight design make it a great choice for any shooter.

While some problems may arise with the weapon, some solutions can help address them.

Proper maintenance and regular cleaning can mitigate or eliminate these issues. We hope this article has given you some insight into the Savage MSR 15 Recon problems and solutions so you can enjoy your rifle even more.

Related Posts:

Savage A22 Magnum Problems

Savage A17 Problems

Kriss Vector Gen 2 Problems

Diamondback DB10 308 Problems

Sig Sauer 716 Problems

Del-Ton AR-15 Problems

Rossi RS22 Problems

Ruger AR-556 MPR Problems